TM 5-6115-586-34
v. Condenser Fans Repair and Replacement
Federal Specification VV-K-
Kerosene .......................
211
Standards.
Trichlorethylene ................. Military Specification MIL-T-
Fan rotation ........................ Counterclockwise viewing fan
7003
wheel end of fan
Special repair compounds and materials:
Duty cycle .......................... Continuous
Brazing alloy ................. Military Specification MIL-B-
Operating current after 10
20148
minutes of operation ...... 15 amperes per phase
Welding ......................... Military Specification MIL-W-
Operating voltage ............... 115/200 vac, 400 Hz, 3
6858
phase
Primer ........................... (Cati-Coat No. 42GP15,
Operating speed after 10
Sherwin Williams Co.,
minutes of operation with
Cleveland, Ohio or
unobstructed airflow ....... 3800 rpm (min)
equivalent; no known
Thermal protector trip time
government specification)
with rotor locked ............ 30 seconds (max)
Enamel .......................... Military Specification MIL-E-
Thermal protector reset
5558 Type II
time after trip ................. 30 seconds (max)
Catalyst .............................. (Cati-Coat No. V66KP15,
Electrical connections to connector:
Sherwin-Williams Co.,
Pin D (white) .................. Neutral
Cleveland, Ohio or
Pin A (green) ................. Phase 1
equivalent; no known
Pin B (red) ..................... Phase 2
government specification)
Pin C (black) ................. Phase 3
z. Cold Water Pump Replacement Standards
Pin E ............................. Not used
Power ............................ 190 Watts (nom)
Weight ............................... 58.0 lb (approx)
270 Watts (max)
Special repair compounds and materials:
Voltage .......................... 115/200 vac, 400 Hz, 3
Remove minor scratches and
Phase
nicks on:
Flowrate ........................ 9 gpm
impeller .......................... Abrasive paper (Federal
Pressure rise ................. 30 psi (nom)
Specification P-P-101, No.
25 psi (min)
400 grit)
Length ........................... 6.9 Inches
Touch up anodic coating on
Width ............................ 4.38 Inches
reworked impeller .......... Anodic Coating Military
Weight .......................... 4.63 lb
Specification MIL-A-8625,
Speed ............................ 11,500 rpm
Type 1)
Duty rating ..................... Continuous
w. Condenser Replacement Standards.
aa. Hot Water Pump Replacement Standards.
Type .................................. Refrigerant gas to air
Power ............................ 190 Watts (nom)
Special cleaning compounds and materials:
270 Watts (maxi
Kerosene ....................... Federal Specification VV-K-
Voltage .......................... 200 vac, 400 Hz, 3 Phase
211
Flow rate ....................... 6 gpm
Trichlorethylene ............. Military Specification MIL-
Pressure rise ................. 23 psi (nom)
T-7003
22 psi (im)
x. Evaporator Replacement Standards.
Length ........................... 7.55 in. (Electrical connector
Type .................................. Air to refrigerant gas
extends approximately 0.50
Special cleaning compound and materials:
in. beyond motor pump)
Kerosene ....................... Federal Specification V V-K-
Diameter ....................... 2.50 in. (Discharge nozzle
211
extends 0.50 in. beyond
Trichlorethylene ............. Military Specification MIL-T-
motor pump
7003
Weight .......................... 2.6 lb maximum
y. Receiver Repair and Replacement Standards:
Speed ............................ 11,500 rpm
Capacity ............................. 30 lb. refrigerant
Duty rating ..................... Continuous
Working pressure ............... 110 psig (nom)
Working pressure ................ 165 psig (max)
ab. Repair and Replacement Standards. Table 1I lists
Weight ............................... 3.8 lb.(approx)
manufacturer's sizes, tolerances, desired clearances, and
Special cleaning compounds and materials:
maximum allowable wear and clearances.
1-4
