TM 5-6115-586-34
Seal nameplate ..................
Zinc chromate primer
Operating input voltage .....
10 to 30 vdc
(Military Specification MIL
Input current ......................
4.5 amperes (max)
P-8585)
Output voltage ...................
18,000 vdc (nom)
Special assembly compounds and materials:
Stored energy ....................
4.3 joules per spark
Lubricate plates,
Weight ..............................
3.5 lb
rings, retainer ................. Lubricating oil (Military
l. Ignition Unit 'Repair and Replacement
Specification MIL-L-7808)
Standards.
e. Starter Assembly Nut and Bolt Torque Data.
Spark rate at 10 volts inputOne spark per second (mini
Starter clutch slip torque ..... 135 to 145 inch-pounds
m. Low Oil Pressure Switch Classification and
f. Fuel Control Assembly Classification and
Rating.
Two single pole double throw
Rating.
Switch type ........................
switches with no internal
Governor type .................... Isochronous
ground
Pump type .......................... Gear
Actuator .............................
Adjustable diaphragm
Lubrication ......................... Fuel
Current capacity ................
4 amperes at 14 to 29 vdc
Proof pressure ...................
.250 psig
cracking pressure .......... 44 to 46 psi
Operating pressure:
g. Fuel Control Repair and Replacement
Actuation ......................
65 psig
Standards.
Deactuation (decreasing
Leakage allowable .............. None
pressure) ......................
55-3 psig
Special repair compounds and
n. Dual Pad Gearcase Repair and Replacement
materials:
Standards.
Magnetic particle inspect,
Magnetic particle inspect nuts Military Specification MIL-I-
shaft, gearshaft .............. Military Specification MIL-I-
6868
6868
Special repair compounds and materials:
Repair minor nicks,
Remove burrs, scratches,
scratches or burrs
nicks .............................
Abrasive cloth (Federal
in non-critical areas ........ Abrasive paper (Federal
Specification P-C-451 or P-
Specification P-P-101, No.
C-458)
600 Grit) or fine stone
Treat aluminum parts after
(Federal Specification AF-3-
corrosion removal .........
Turco Prepaint (Turco
JB)
Products, Inc., Los Angeles,
h. Fuel Control Unit Nut and Bolt Torque Data.
California, or equivalent;
Screw to secure cover to
no known government
housing .......................... 40 to 60 inch-pounds
specification) or Brush
Nut to secure fitting to
Alodine (American Chemical
housing .......................... 100 to 110 inch-pounds
Paint Co., Ambler, Penn.or
i. Fuel Shutoff Solenoid Valve Classification and
equivalent; no known
Rating.
Reanodize aluminum parts
Valve actuator .................... Electromagnet
Military Specification MIL-A-
as required ...................
Normal valve position ......... Closed
8625
Operating pressure ............. 0 to 1000 psig
Strip paint .....................
Kestrip "E" (Kelite Products,
Operating voltage ............... 11 to 30 vdc
Los Angeles, California, or
Operating current ............... 1.0 amp (max) at 28 vdc
equivalent; no known
Drop out voltage ................. 4 vdc (mini
government specification)
Flow .................................. 500 phr (pounds per hour)
Prime parts to be painted Primer (Military Specification
(max)
MIL-P-8585)
Pressure drop across valve
Paint parts ....................
Black enamel (Military
at 120 phr (pounds per
Specification MIL-E-5557,
hour) flow ...................... 4 psig (max)
Type II)
Weight ............................... 0.3 lb
Special assembly compounds and
j. Fuel Shutoff Solenoid Valve Repair and
materials:
Replacement Standards.
Coat sealing bore of retainer Cement (Glyptal, No. 1276,
Valve leakage at 300 psig
General Electric Co.,
fluid pressure ................. 0.5 cc (cubic centimeters) per
Schenectady, New York, or
Valve leakage at 1000 psighour (max)
equivalent; no known
fluid pressure ................. 1.0 cc per hour (max)
government specification)
Operating voltage at 100 -.3
o. Dual Pad Accessory Torque Values.
psig fluid pressure ......... 7.2 vdc (min)
Nut to gearshaft .................
145 to 15 inch-pounds
Operating voltage at 300 +/- 3
Nut to gearshaft .................
145 to 155 inch-pounds
psig fluid pressure ......... 9.0 vdc (min)
Nut to gearshaft .................
145 to 155 inch-pounds
p. Accessory Gearcase Repair and Replacement
k. Ignition Unit Classification and Rating.
Standards
Type. .................................. High voltage, capacitor
Magnetic particle inspect, jaw Military Specification MIL-I-
discharge
6868
Enclosure ............................ Hermetically sealed
1-2