e. Installation.
screw (25), washer (26) and nut (27). Re-
(1) Slide drip pan (78) into skid (79).
move panels (28 and 29) by removing screw
(2) Install drip rail (80) on panel (5)
(30) and nut (31).
using screws (81).
(6) Remove door jam (32) by removing
(3) Secure heater strap (84) on mani-
screw (33) and nut (34).
fold with screw (36), nut (37) and washers
(7) Remove battery retainer (35) by re-
(38).
moving holddown stud (36), nut (37), and
washer (38). Remove batteries (39).
(4) Install connector (24) on panel (20)
(8) Remove battery box (40) from rails
with screw (27), washer (26) and nut (27).
(82), then remove radiator shell (43). Re-
(5) Install panel (71) in shell (75) using
move door (46) from shell (43).
screw (72) and nut (74).
(9) Remove radiator (49) and cap
(6) Install rear shell (75) using screw
(76) and nut (77).
(50), then remove shroud (51) from radiator.
(10) Remove bracket (53) by removing
(7) Install hoses (63 and 65) on bracket
screw (54) washer (55) and nut (56).
(66) using clamps (64).
(11) Remove tank (57) and strainer (58)
(8) Install brackets (61 and 62) rails
from rails (59 and 60), then remove rails.
(59 and 60) then install fuel tank (57). In-
(12) Remove brackets (61 and 62) then
stall strainer (58) in fuel tank.
remove hose (63), clamp (64) and hose (65).
( 9 ) Install bracket (53) using screw
(13) Remove bracket (66) and remote box
(54), washer (55) and nut (56).
(67), then remove cover (68) by removing
(10) Install cover (68) on box (67) with
screw (69) and washer (70).
screws (69) and washer (70). Install box (67)
( 1 4 ) Remove panel (71), then remove
on bracket (53).
( 1 1 ) Install shroud (51) using screws
shell (75) from skid (79).
(15) Remove drip pan (78) from skid (79)
(52).
(12) Install radiator (49) and cap (50).
and drip rail (80) from top panel (5).
(13) Install shell (43) using screws (44)
b. Cleaning. Wipe grease, dirt and dust from
panels and doors with solvent dampened cloth.
and nut (45), then install door (46) using
screw (47) and nut (48).
Wipe oil drip pan, shutter assemblies and shell
(14) Install door jam (32) using screw
assemblies with solvent dampened cloth. If
particularly dirty, clean enclosure and frame
(33) and nut (34).
(15) Install center panels (28 and 29) us-
with live steam and solvent before wiping
ing screws (30) and nuts (31).
with cloths.
(16) Install instrument panel (20). Install
c. Inspection. Inspect doors, panels, frames,
ground strap (23), then install cover (21) us-
brackets, and shell assemblies for breaks,
ing screws (22).
dents, cracks, or damaged paint. Make sure
(17) Install radiator hoses (17 and 18)
doors close securely and latches operate prop-
e r l y . Inspect lifting frame for broken or
using clamps (19).
(18) Install exhaust tube (8) using clamps
cracked welds and stretched or broken attach-
ing screw holes and lifting eye.
(9 and 10), then install hose and elbow (12).
d. Repair. Straighten bent doors and panels
(19) Install rain cap (13) using screws
and weld members. Replace defective door
(14) nut (15) and cotter pin (16).
latches. Replace defective shutter assemblies
(20) Install top panel (5) using screws
as a unit. Repair small leaks in radiator with
(6) and nut (7).
solder. Do not permit solder to flow into radi-
(21) Install side doors (1) using screws
ator core. If radiator is excessively damaged,
(2 and 3) and nuts (4).
corroded, or clogged, replace. Replace cap and
drain cock if damaged or defective. Replace
6-17. Enclosure
a. Disassembly.
batteries which do not pass inspection with
(1) Remove side doors (1) by removing
fully charged batteries known to be in good
screws (3) and nuts (4).
condition. Replace defective hold-down hard-
ware.
123