coda
pair parts quantities included in the kits, sets, and
Explanation
be requisitioned with supporting justification
assemblies are shown in front of the repair part
through normal supply channels.
name.
Applied to repair parts authorized for local pro-
C
d. Unit of Issue. Indicates the unit used as a
curement. If not obtainable from local procure-
ment, such repair parts will be requisitioned
basis for issue, e.g., ea, pr, ft, yd, etc.
through normal supply channels with a sup-
porting statement of nonavailability from local
e. Quantity Incorporated in Unit Pack. Indi-
procurement.
cates the actual quantity contained in the unit
Applied to major assemblies that are procured
G
pack.
with PEMA (Procurement Equipment Missile
f. Quantity Incorporated in Unit. Indicates the
Army) funds for initial issue only to be used as
exchange assemblies at DSU and GSU mainte-
quantity of the item used in the functional group.
nance level. These assemblies will not be stocked
above DSU and GSU level or returned to depot
g. Fifteen-Day Organizational Maintenance Al-
level.
lowances.
(2) Maintenance Code. Indicates the lowest
(1) The allowance columns are divided into
category of maintenance authorized to install the
four subcolumns. Indicated in each subcolumn op-
listed item. The maintenance codes are:
posite the first appearance of each item is the total
quantity of items authorized for the number of
Code
Explanation
o
Organizational maintenance
equipments supported. Items authorized for use as
F
Direct support maintenance
required but not for initial stockage are identified
General support maintenance
H
with an asterisk in the allowance column.
(3) Recoverability Code. Indicates whether
(2) The quantitative allowances for organiza-
unserviceable items should be returned for recov-
tional level of maintenance represents one initial
ery or salvage. Items not coded are expendable.
prescribed load for a 15-day period for the num-
Recoverability codes are:
ber of equipments supported. Units and organiza-
Code
Explanation
tions authorized additional prescribed loads will
Applied to repair parts and assemblies which are
R
multiply the number of prescribed loads author-
economically repairable at DSU and GSU ac-
ized by the quantity of repair parts reflected in the
tivities and which are normally furnished by
appropriate density column to obtain the total
supply on an exchange basis.
quantity of repair parts authorized.
Applied to repair parts and assemblies which are
S
economically repairable at DSU and GSU ac-
(3) Organizational units providing mainte-
tivities and which normally are furnished by
nance for more than 100 of these equipments shall
supply on an exchange basis. When items are
determine the total quantity of parts required by
determined by a GSU to be uneconomically re-
pairable, they will be evacuated to a depot for
converting the equipment quantity to a decimal
evaluation and analysis before final disposition.
factor by placing a decimal point before the next
T
Applied to high dollar value recoverable repair
to last digit of the number to indicate hundredths,
parts which are subject to special handling and
and multiplying the decimal factor by the parts
are issued on an exchange basis. Such repair
quantity authorized in the 51-100 allowance col-
parts are normally repaired or overhauled at
umn. Example, authorized allowance for 51-100
depot maintenance activities.
equipments is 12; for 140 equipments multiply 12
Applied to repair parts specifically selected for
U
by 1.40 or 16.80 rounded off to 17 parts required.
salvage by reclamation units because of pre-
cious metal content, critical materials, high
(4) Subsequent changes to allowances will be
dollar value reusable casings or castings.
limited as follows: No change in the range of
(4) This column also lists, below the SMR
items is authorized. If additional items are consid-
code, an index number for each item in ascending
ered necessary, recommendation should be for-
numerical sequence, which is used to locate items
warded to U. S. Army Mobility Equipment Com-
in the publication when the Federal stock number
mand for exception or revision to the allowance
and/or reference number is known.
list. Revisions to the range of items authorized
will be made by this Command based upon engi-
b. Federal Stock Number. Indicates the Federal
neering experience, demand data, or TAERS in-
stock number for the item.
formation.
c. Description. Indicates the Federal item name
h. Thirty-Day DS/GS Maintenance
Allowances.
and any additional description of the item re-
(1) The allowance columns are
divided into
quired. A part number or other reference number
three subcolumns. Indicated in each
subcolumn,
is preceded by the applicable five-digit Federal
opposite the first appearance of each
item, is the
supply code for manufacturers in parentheses. Re-
D-2
