0042 00
TM 1-4920-434-13&P
REPAIR OR REPLACEMENT
SHELF CABINET (C)
1.
If cabinet brackets (Figure 4, Item 13) can be repaired by welding, weld damaged area IAW TM
1-1500-204-23. Repair must not interfere with form, it, or function of cabinet brackets (Figure 4, Item 13).
2.
Paint repaired cabinet brackets (Figure 4, Item 13) IAW WP 0069 00, Figure 6.
INSTALLATION
SHELF CABINET (C)
1.
If a new work surface (Figure 4, Item 4) must be installed:
a.
Position work surface (Figure 4, Item 4), inished side up, on top of shelf cabinet (C) (Figure 4, Item 5).
b.
Ensure work surface (Figure 4, Item 4) is lush with back and sides of shelf cabinet (C) (Figure 4, Item 5).
c.
On inside of shelf cabinet (C) (Figure 4, Item 5), mark four hole placements (Figure 4, Item 14) in top of
shelf cabinet (C) (Figure 4, Item 5) on non-inished side of work surface (Figure 4, Item 4).
d.
After four hole placement marks (Figure 4, Item 14) have been made, lip work surface (Figure 4, Item
4) over with non-inished side up.
e.
On non-inished side of work surface (Figure 4, Item 4) at four marked hole placements (Figure 4, Item
14), center punch and drill four 5/16 inch holes to a depth of 3/4 inch.
2.
Align bolt holes of work surface (Figure 4, Item 4) with bolt holes on top of shelf cabinet (C) (Figure 4, Item 5).
3.
Install four lag bolts (Figure 4, Item 1), four lock washers (Figure 4, Item 2), and four lat washers (Figure 4,
Item 3) securing work surface (Figure 4, Item 4) to shelf cabinet (C) (Figure 4, Item 5).
4.
Install four bolts (Figure 4, Item 12), eight lat washers (Figure 4, Item 11), four lock washers (Figure 4, Item
2), and four nuts (Figure 4, Item 10) securing two cabinet brackets (Figure 4, Item 13) into shelf cabinet (C)
(Figure 4, Item 5).
5.
If new shelf cabinet (C) (Figure 4, Item 5) has been installed:
a.
Use holes (Figure 4, Item 4 through 9) of existing work surface (Figure 4, Item 4) to determine drill bit
sizes.
b.
Match drill holes of work surface (Figure 4, Item 4) through shelf cabinet (C) (Figure 4, Item 5).
6.
If a new work surface (Figure 4, Item 4) has been installed and/or a new work surface and shelf cabinet (C)
(Figure 4, Item 5) has been installed:
a.
Measure from right side of work surface (Figure 4, Item 4) towards left 16.00 inches and from front of
work surface (Figure 4, Item 4) towards back 22.25 inches and mark measurement (Figure 4, Item 7).
b.
Measure from right side of work surface (Figure 4, Item 4) towards left 3.50 inches and from front of work
surface (Figure 4, Item 4) towards back 22.25 inches and mark measurement (Figure 4, Item 9).
c.
Measure from right side of work surface (Figure 4, Item 4) towards left 16.00 inches and from front of
work surface (Figure 4, Item 4) towards back 4.00 inches and mark measurement (Figure 4, Item 6).
d.
Measure from right side of work surface (Figure 4, Item 4) towards left 3.50 inches and from front of work
surface (Figure 4, Item 4) towards back 4.00 inches and mark measurement (Figure 4, Item 8).
e.
Center punch and drill four 1/2 inch holes (Figure 4, Item 6 through 9) through work surface (Figure 4,
Item 4) and shelf cabinet (C) (Figure 4, Item 5).
7.
Install hardware attaching shelf cabinet (C) (Figure 4, Item 5) to shelter loor IAW WP 0043 00, Cabinets (C),
(D), and (E) Hardware, INSTALLATION.
8.
Install drawers, slides, and shelves as necessary IAW Drawers, Slides, And Shelves, INSTALLATION.
9.
Install kick plate IAW Kick Plate, INSTALLATION.
0042 00-8