(1) First. Using the Index of Federal Stock
not for initial stockage are identified with an
Numbers and Reference Numbers find the per-
asterisk in the allowance column.
(2) The allowance columns are divided into
tinent Federal stock number or reference number.
This index is in ascending FSN sequence followed
three subcolumns. The quantitative allowance of
by a list of reference numbers in alpha-numeric
s p e c i a l tools for DS level of maintenance will
sequence, cross-referenced to the illustration figure
represent initial stockage for a 30-day period for the
number and item number.
number of equipments supported. When special
(2) Second. Using the Repair parts listing,
tools are not required, enter statement "Not Ap-
find the assembly group of the repair part and the
plicable".
illustration figure n u m b e r a n d i t e m number
j. One-Year Allowances Per 100 Equip-
referenced in the index of Federal Stock Numbers
ment/Contingency
Planning
Purposes.
and Reference Numbers.
(1) Items authorized for use as required but
c. When the Federal Stock Number or
n o t for initial stockage are identified with an
Reference Number is Known and the Repair Part
asterisk in the allowance column.
is Not Illustrated:
(2) This column indicates the total quantity of
(1) First. Using the index of Federal Stock
special tools required for distribution and con-
Numbers and Reference Numbers find the per-
tingency planning purposes.
tinent Federal stock number or reference number in
k. Depot Maintenance Allowance Per 100
the section titled "Items Not Illustrated" and note
Equipment. (Not Applicable)
the group number. This section is in ascending
l. Illustration. This column is divided as
F S N sequence followed by a list of reference
follows:
n u m b e r s i n a l p h a - n u m e r i c sequence cross-
(1) Figure number. Indicates
t h e figure
referenced to assembly group number.
nomber of the illustration on which the item is
(2) S e c o n d . Using the Table of Contents,
shown.
(2) Item number. Indicates the callout
locate the assembly group number and page
number.
number used to reference the item on the
(3) T h i r d . U s i n g t h e a p p l i c a b l e g r o u p
illustration.
number and page number, locate the pertinent
C-4. Special Information
stock number or reference number in the Repair
a. Parts which require manufacture or assembly
Parts Listing.
of a maintenance level higher than that authorized
C-6.
Abbreviations
for installation will indicate column the higher
maintenance level.
b. The same illustrations are used to illustrate
the repair parts and special tools listed in both
o r g a n i z a t i o n a l maintenance section and direct
support maintenance section.
C-5. How to Locate Repair Parts
a. When the Federal Stock Number or
R e f e r e n c e Number is Unknown:
(1) First. U s i n g t h e t a b l e o f c o n t e n t s ,
determine the assembly group within which the
repair part belongs. This is necessary since
illustrations are prepared for assembly groups, and
C-7. Recommendations for Maintenance
listings are divided into the same groups.
Publications Improvements
(2) Second. Find the illustration covering the
Report of errors, omissions, and recommendations
assembly group to which the repair part belongs.
for improving this publication by the user is en-
(3) T h i r d . Identify the repair part on the
c o u r a g e d . Reports should be submitted on DA
illustration and note the illustration' figure and item
Form
2028 (Recommended Changes to
number of the repair part.
Publications) and forwarded direct to Com-
(4) Fourth. Using the Repair Parts Listing,
manding General, U. S. Army Mobility Equipment
find the assembly group to which the repair part
Command,
ATTN:
AMSME-MPP,
4300
belongs and locate the illustration figure and item
Goodfellow Boulevard, St. Louis, Mo. 63120.
number noted on the illustration.
b. When the Federal Stock Number or
Reference Number is Known: