INTRODUCTION
Explanation
Code
1. Scope
M
Repair
parts
which
are
not
procured
or
stocked,
This manual lists repair parts required for the
but
m-e
to
be
manufactured
in
indicated
mainte-
performance of direct support, general support,
nance
levels.
and depot maintenance of the welding machine.
A
Assemblies
which
are
not
procured
or
stocked
as
such,
but
are
made
up
of
two
or
more
units.
Such
component
units
carry
individual
stock
2. General
are
procured
and
numbers
and
descriptions,
stocked
separately
and
can
be
assembled
to
form
This Repair Parts and Special Tools List is di-
the
required
assembly
at
indicated
maintenance
vided into the following sections:
categories.
Parts
and
assemblies
which
are
not
procured
or
X
stocked
and
the
mortality
of
which
normally
is
parts authorized for the performance of mainte-
below
that
of
the
end
item
or
component.
The
nance at the direct support, general support, and
failure
of
such
part
or
assembly
should
result
depot level in figure and item number sequence.
in
retirement
of
the
end
item
from
the
supply
system.
b. Special Tools, Test and Support Equipment-
X1
Repair
parts
which
are
not
procured
or
stocked.
Seciton III. A list of special tools, test and support
The
requirement
for
such
items
will
be
filled
equipment authorized for the performance of
by
use
of
the
next
higher
assembly
or
component.
maintenance at the direct support, general sup-
X2
Repair
parts
which
are
not
stocked.
The
indicated
port, and depot level. (Not applicable.)
maintenance
category
requiring
such
repair
parts
will
attempt
to
obtain
same
through
cannibaliza-
c. Index-Federal Stock Number and Reference
tion.
Where
such
repair
parts
are
not
obtainable
through
cannibalization,
requirements
will
be
re-
numbers in ascending numerical sequence fol-
quisitioned,
with
accompanying
Iowed by a list of reference numbers in ascending
through
normal
supply
channels.
alpha-numeric sequence, cross-referenced to the
G
Major
assemblies
that
are
procured
with
PEMA
funds
for
initial
issue
only
as
exchange
assemblies
illustration figure number and item number.
at
DSU
and
DSU
level.
These
assemblies
will
Note. Items not, illustrated are cross-referenced to
not
be
stocked
above
DSU
and
DSU
level
or
page number.
returned
to
depot
supply
level.
3. Explanation of Columns
category of maintenance authorized to install the
The following provides an explanation of columns
listed item. Repair parts and special tools assigned
maintenance code "C" may be stocked at the oper-
ator level of maintenance when authorized by the
a. Source, Maintenance, and Recoverability
Unit Commander. The maintenance level codes
Codes (SMR).
are:
(1) Source code indicates the selection status
Code
Explanation
and source for the listed item. Source codes used
C... . . . . . . . . Crew
or
operator
maintenance
are:
O.
.
.
.
.
.
.
.
.
.
.-
Organizational
maintenance
Code
Explanation
F...
.
.
.
.
.
.
..
.
.
Direct
support
maintenance
P
Repair
parts
which
are
stocked
in
or
supplied
from
H.
.
.
.
.
.
.
.
.
.
..
General
support
maintenance
the
GSA/DSA,
or
Army
supply
system
and
D . . . . . .. . . . .
.. . . . .
Depot maintenance
authorized
for
use
at
indicated
maintenance
cate-
gories.
(3) Recoverability code indicates whether
P2
Repair
parts
which
are
procured
and
stacked
for
unserviceable items should be returned for re-
purposes
because
the
combat
or
military
covery or salvage. Items not coded are expendable.
essentiality
of
the
end
item
dictates
that
a
mini-
Recoverability Codes are:
mum
quantity
be
available
in
the
supply
system.
iii